Product Name: Rigid PVC Edgebanding
Product Usage: A continuous extruded roll available in various thicknesses used to finish the raw edge of HPL, flake boards plywood and medium density fiberboard. Available in various colors that matches with most of the laminated panels
Hazardous Ingredients:
This product contains no Hazardous Ingredients that can be released under normal temperature or working conditions. Rigid PVC Edgebanding contains no vinyl chloride monomers.
| Description | Unit | Value | Standard |
|---|---|---|---|
| Hardness Shore | - | D - 78 ± 4 | ISO868 |
| Shrinkage (1h at 140°F (60°C)) | % | < 0.5 | Works Standard |
| Static Charging | - | Low | - |
| Vicat Softening Temperature (At 50N) | °C | 80.3 | ASTM D1525-2009 |
| Description | Unit | Value | Standard |
|---|---|---|---|
| (a) Change in Thickness | % | 4.2 | IS:2046-1995 |
| (b) Change in Mass | % | 3.9 | IS:2046-1995 |
| (c) Appearance | Degree | 5 | IS:2046-1995 |
| Description | Unit | Value | Standard |
|---|---|---|---|
| (a) At Dry Staining | Rating | 4/5 | IS:766-1988 |
| (b) At Wet Staining | Rating | 4/5 | IS:766-1988 |
| Description | Unit | Value | Standard |
|---|---|---|---|
| (a) Type of lamp | UV A340 | No cracks or blister observed | ASTM G154-2016 |
| (b) Exposure Time | 24 hour | No cracks or blister observed | ASTM G154-2016 |
| Description | Unit | Value | Standard |
|---|---|---|---|
| Appearance | Rating | 4 | IS:2046-1995 |
| Description | Unit | Value | Standard |
|---|---|---|---|
| (a) Acetone | Rating | 5 | IS:2046-1995 |
| (b) Black Tea | Rating | 5 | IS:2046-1995 |
| Description | Unit | Value | Standard |
|---|---|---|---|
| Cease to burn before | mm | 25 | mark |
| Cease to burn before the | mm | 100 | Reference Mark |
| Description | Value |
|---|---|
| State | Solid |
| Boiling Point | NA |
| Specific Gravity | 1.20 to 1.40 |
| Solubility | Insoluble |
| Volatility | Negligible |
| Machining | PVC Suitability |
|---|---|
| Cutting | Good |
| Milling Direction | Counter Direction |
| Pre-milling | Good |
| Radius Milling | Good |
| Profiling | Good |
| Scraper Processing | Good |
| Buffing | Good |
| Bonding | Any conventional hot-melt adhesive suitable for edging tapes can be used |
| Polish Ability | Good |
| Stress Whitening | Low |
| Machining Center Processing Compatibility | Very Good |
1. Color: Slight color variations are possible from dye lot to dye lot.
2. Finishes: Available in Gloss, Matt & SF.
3. Finish must be smooth and free of defects at a distance of 3 feet from the observer.
4. Material either has UV inhibitors directly in the resin or has a UV topcoat.
5. Interior Use: Only for interior use and not to be exposed to temperatures above 150°F.
6. Primer: Backside is 100% covered with a primer for proper bond.
7. Maintenance: Clean surface with warm soapy water and wipe clean.
| Width mm | Tolerance mm |
|---|---|
| 12 – 55 | ± 0.45 |
| Width mm | Tolerance mm |
|---|---|
| 0.4 - 0.7 | ± 0.05 |
| 0.8 - 1.5 | ± 0.10 |
| 1.6 - 2.0 | + 0.20 |
| 2.1 - 3.0 | + 0.25 |
PVC Edge Banding tape is resistant to rot and may therefore be stored at room temperature (64°F to 68°F) in a room that is weatherproof and protected
from direct sun light for a virtually unlimited period.
Using accepted industry standards, colors, woodgrains, and patterns have been individually matched and cross-referenced for the best suitable match. Color variation beyond the manufacturers’ control may occur in individual resin batches. The manufacturers’ warranty and liability for the bond, color match, and surface finish; extend only to the replacement value of the specific edgebanding material. It is the customer’s sole responsibility to determine that the bond and color match are acceptable for production before use.
